Latest news from ReprapWorld

Written by Mike Santifort on 2019-03-23 13:10:36

Hello,

today we're going to explain how to upgrade your CR-10S Pro with an E3D V6 Hot end.

Firstly print this E3D v6 Mount: Click here.

Then we can start by unscrewing the metal fan holder.
Then we get access to the place where we can remove the old hot end.

Once you have unscrewed the old hot end you can start the assembly of the E3D V6 hot end, for wich you can follow this guide:Click here.

After you have assembled the new hot end we can start mounting it, for this we need our printed part.
Firstly we will screw in the backplate of our printed part,
we do this upside down so we have more space for our print.

After that you can place in the new E3D V6 hot end and place over the front piece we printed. Screw it tight so you cant turn the E3D V6  hot end.

After that you need to recalibrate the leveling sensor, You can use this guide for that:

Written by Mike Santifort on 2019-03-19 00:00:00

Hello,

Today we are going to explain how to correctly align the CR-10S Pro leveling sensor.

We can start by unscrewing the metal fan holder,
Then we get access to the place where the sensor is attached to the moving head.

 

Now it's the trick to lower the nozzle on to the bed and loosen the 2 grip screws on the left side of the sensor,
then lower the sensor until 3mm off the bed and fasten the 2 grip screws.

 

After that we lower the sensitivity of the leveling sensor and we redo the z homing process, redo this until it lowered the nozzle to touch the bed.

 

If you have done this correctly the leveling sensor will behave way more accurate and you would have to less re-calibrate the leveling!

You're done, enjoy a much smoother leveling process!

Written by Bart Meijer on 2019-03-12 08:28:37

We now have 3D printing optimized PLAs available as well as TPU and PA. All products including their datasheet. Check out the pellets section for more information.

Written by Bart Meijer on 2019-01-09 18:44:43

Our assortment of heater cartridges has been extended with not only 150 and 200cm long heater cartridges, but also black versions of the 100cm cartridges.

Check out the heater cartridges section for more information

Written by Bart Meijer on 2018-11-28 09:51:44

We have expanded our assortment of products with new products for prototyping electronics. This includes PCB boards, Jumper wires and Breadboards. Now you can practice your soldering skills or quickly make a setup for testing a new component.

Perché ReprapWorld?
  • Spedizione nello stesso giorno lavorativo!
  • Più di 2.000 prodotti disponibili a magazzino
  • Più di 25.000 clienti soddisfatti in più di 40 paesi
  • Pagamenti sicuri con qualsiasi metodo
  • Supporto tecnico professionale (più di 9 anni di esperienza nel campo della stampa 3D)
Più di 25.000 clienti soddisfatti

4.3 stelle su Google

Paga in sicurezza utilizzando

Informazioni su ReprapWorld
ReprapWorld

ReprapWorld è il negozio online numero uno per tutti i prodotti reprap per la tua stampante 3D. Abbiamo a disposizione un'ampia gamma di componenti per stampanti 3D, dalla nostra celebre linea di componenti elettronici ai filamenti ai nostri prodotti personalizzati. E tutto ciò a un prezzo molto competitivo!

Contatti

RepRapWorld B.V.
Wagenmaker 6a
2631RL Nootdorp
The Netherlands

Email: info@reprapworld.com
Tel: +31 (0) 85 - 009 15 31

Copyright 2009 - 2017 | RepRapWorld B.V.