PrintHat v1 - 32-bit motor controller board for Raspberry Pi

Extension board to the Raspberry PI, allowing you to run a 3D printer
  • Fast, space efficient daughter board for Raspberry Pi
  • Runs Klipper firmware with Octoprint controller using customized Raspbian OS
Disponibilitá: 2
€ 90,89  incl. IVA Disponibile

Solo 2 rimasti, ordina subito!

Descrizione prodotto

Fast, space efficient daughter board for Raspberry Pi. Runs Klipper firmware with Octoprint controller using customized Raspbian OS.

The WreckLab PrintHAT is a high performance controller board for the Raspberry Pi and currently the only such board on the market specifically designed around the increasingly recognized firmware called "Klipper", the new kid-on-the-block in the 3D printing community. In simple terms: Klipper's architecture is designed to distribute the computational overhead for high speed, high resolution motor steps to a powerful microcomputer (e.g. Raspberry Pi), freeing up the controller board to execute those steps with greater smoothness and precision.

The PrintHAT is directed primarily at printing enthusiasts and small businesses who are looking into (or already using) OctoPrint as one of their primary 3D printer controller interfaces, since Klipper (and PrintHAT by extension) have been extensively built around OctoPrint's well established and highly developed GUI. While the PrintHAT & Raspberry Pi work behind the scenes, Octoprint provides the user with an advanced, flexible and highly extensible Human-to-Machine controller interface, which now include integrated options for automated processes (macros), event-driven interrupts (filament runout sensors) and web cameras.

Transitioning from other controllers and firmwares? No problem! The PrintHAT comes with a dummy-proof installer package that makes installation a breeze for busy beginners, while also being customizable to the requirements of more experienced users. Whether you are in the market for a new machine or wish to upgrade your current configuration, the PrintHAt + Raspberry Pi configuration packs features, power and convenience in a small, clean form factor with minimum hassle and plenty of documentation.

NOTE: A Raspberry Pi is required to operate the printHAT and must be obtained separately. PrintHAT is compatible with Raspberry Pi v0/1/2/3, but the best performance is obtained with v2 & 3.


  •     Powerful 32 Bit ARM Cortex processor (TM32F103)
  •     9-26V input voltage
  •     4x TMC2130 stepper drivers
  •     Enhanced endstop accuracy with the stepper phase detection smart correction
  •     Sensorless homing
  •     StealthChop supported for extremely quiet operation and smooth motion
  •     Up to 256 microsteps per full step
  •     4x PWM output (up to 10A per channel)
  •     8x GPIOs fully configurable (endstops, filament sensor, etc)
  •     2x ADC input

Package contents:

  • 1x printHAT board
  • 1x boot jumper
  • 1x 2x2 pin header
  • 3x Molex 395100002
  • 1x Mounting Kit (2x M2.5x11 hex spacers,4x M2.5x5 Phillips screws)


Tecnologia ARM
Tipo Cortex
Frequenza 72 MHz
Lunghezza 87 mm
Profondità 56 mm
Altezza 10 mm
Termistori 2
Finecorsa 8
Stepper driver 4
Scheda SD esterna
WIFI (w/ Pi)
Input separato per piatto riscaldato
€ 90,89  incl. IVA Disponibile

Solo 2 rimasti, ordina subito!


1 - 9: IVA escl. € 75,12 incl. € 90,89
10 - 29: IVA escl. € 71,36 incl. € 86,35
30 - : IVA escl. € 67,60 incl. € 81,80
Hai bisogno di una quantità superiore di questo prodotto? Contatta il nostro Ufficio Vendite.

Related products

Opto endstop PCB TCST-2103
  € 7,25

Informazioni su ReprapWorld

ReprapWorld è il negozio online numero uno per tutti i prodotti reprap per la tua stampante 3D. Abbiamo a disposizione un'ampia gamma di componenti per stampanti 3D, dalla nostra celebre linea di componenti elettronici ai filamenti ai nostri prodotti personalizzati. E tutto ciò a un prezzo molto competitivo!


RepRapWorld B.V.
Klopperman 7
2292JE Wateringen
The Netherlands

Tel: +31 (0) 85 - 009 15 31

Copyright 2009 - 2021 | ReprapWorld B.V.